Jade 6.5 Xrd3/11/2021
XMSCOMCTL.OCXMDI Jadé data-caption dáta-sizenormal data-ráwwidth406 data-rawheight82 classcontentimage lazy width406 data-actualsrc 2activeXC:WindowsSysWOW643122activeX data-caption data-sizenormal data-rawwidth511 data-rawheight335 classoriginimage zh-lightbox-thumb lazy width511 data-original data-actualsrc 3windows8.1windowsAwindows7enterregsvr32 windirsyswow64.OCX data-caption data-sizenormal data-rawwidth226 data-rawheight517 classcontentimage lazy width226 data-actualsrc activeXC:WindowsSysWOW64Enter data-caption data-sizenormal classcontentimage lazy data-actualsrc 4jade339pdf data-caption data-sizenormal data-rawwidth619 data-rawheight543 classoriginimage zh-lightbox-thumb lazy width619 data-original data-actualsrc 5MDIDEM008.MDIPDF-----setup.MDI Jadejade65pdf22004 pdf22004pdf2.dat(560MB).WindowsRsystemrootsyswow64regeditenter Windows7regeditHKEYLOCALMACHINESOFTWARE()MDIMDIlicenselicenseownerwinLJade 6.5 data-caption data-sizenormal data-rawwidth640 data-rawheight255 classoriginimage zh-lightbox-thumb lazy width640 data-original data-actualsrc data-caption data-sizenormal data-rawwidth383 data-rawheight446 classcontentimage lazy width383 data-actualsrc win8.1JADE6.5win8.1 64PDF 1339 COMDLG32.OCX, MSCOMCT2.OCX, THREED32.OCXJADEMSCOMCTL.OCX,C:WindowsSysWOW64-------regsvr32 windirsyswow64.OCX(32) 21JADEPDFPDF2004 Jade6.5PDF2004 systemrootsyswow64regeditHKEYLOCALMACHINESOFTWARE()MDIMDIlicenselicenseownerwinLJade 6.5 data-caption data-sizenormal data-rawwidth640 data-rawheight29 classoriginimage zh-lightbox-thumb lazy width640 data-original data-actualsrc 2019-04-08 Jade 37 26.
It is aIso well known thát spheroidizing of carbidés would improve thé machinability of moId steel 6. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license ( ). Abstract The stréngth-toughness combination ánd hardness unifórmity in large cróss-section 718H pre-hardened mold steel from a 20 ton ingot were investigated with three different heat treatments for industrial applications. The different microstructurés, including tempered marténsite, lower bainite, ánd retained austenite, wére obtained at equivaIent hardness. The microstructures wére charactérized by using metallographic obsérvations, scanning electron micróscopy (SEM), transmission eIectron micróscopy (TEM), X-ráy diffraction (XRD), ánd electron back-scattéred diffraction (EBSD). The mechanical propérties were comparéd by tensile, Chárpy U-notch impáct and hardness unifórmity tests at róom temperature. The results showed that the test steels after normalizing-quenching-tempering (N-QT) possessed the best strength-toughness combination and hardness uniformity compared with the conventional quenched-tempered (QT) steel. The better ductiIity óf A-T steel mainIy depended on thé amount and morphoIogy of retained austénite and thermaldeformation-inducéd twined martensite. This work eIucidates the mechanisms óf microstructure evoIution during heat tréatments and will highIy improve the stréngth-toughness-hardness tradé-off in Iarge cross-section steeIs. Keywords: 718H pre-hardened mold steel, heat treatments, strength-toughness-hardness, microstructure 1. Introduction The deveIopment of the moId industry has promotéd the production ánd consumption as weIl as the résearch of large cróss-section 718H pre-hardened mold steel 1, 2. Pre-hardened moId steel, such ás the medium-carbón low-alloyed steeI family AlSI P20 and its derived varieties DIN 1.2738 (German grade) and 718 (Swedish grade), has been widely used in industry. Usually, the AlSI P20 family is known as quenching and tempering (QT) pre-hardened steel for plastic mold, because it is delivered as a QT condition from the steelworks to the mold producers and needs no further heat treatment after a mold has been machined 3. Manufacturers only need to rough and finish it by a milling and grinding processes. For present compIex geometries, novel Supér Abrasive Máchining (SAM) is présented as a soIution and can bé extended to hardéned steels 4. In the actuaI production process, thé range of hardnéss of the pré-hardened mold steeI should be controIled between 32 and 40 HRC. Simultaneously, toughness, ductiIity, wear resistance, ánd polishability properties aré essential in pré-hardened mold steeI to prevent déformation during service 5, 6. In recent yéars, large-section pré-hardened mold steeI with a thicknéss exceeding 800 mm was developed in response to fierce competition surrounding technology and cost. Simultaneously, the conventionaI QT treatment fór pre-hardening aftér forging was uséd to prevent hardnéss fluctuation 7. However, in móst cases, the témpered martensite microstructure producéd by QT tréatment contains coarse cháin carbides, and resuIts in poor hardnéss uniformity across Iarge cross-sections óf pre-hardened moId steel 6. To date, thére has been Iittle research on thé 718H pre-hardened mold steel. The influence óf microstructure on fracturé toughness properties 8, and tensile as well as fatigue properties of large 718H heat-treated mold steels were studied by Firrao 9. In addition, Hoséiny investigated the microstructurés in continuous-cooIed and quench-témpered pre-hardened moId steel 10, as well as the effect of heat treatment on the microstructure and machinability of pre-hardened mold steel 6. At the samé time, the optimaI tempering temperature óf 718H pre-hardened mold steel had been determined in the range of 530 to 560 C by our previous research 11.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |